Introducing the Mobula7 1S HD 75mm Whoop Drone
The Mobula7 1S HD version is a lightweight and efficient 75mm brushless whoop that provides 1080P high-definition video recording capabilities. Featuring a highly integrated All-In-One (AIO) flight controller supporting ESC with a maximum current output of 12A, this drone is a top choice for capturing stunning aerial footage. With added blackbox support for gyroflow stabilization, enjoy safe and smooth flights while recording high-quality videos.
Notable Features
- X12 5-IN-1 AIO flight controller
- VTX Power up to 400mw ELRS V2.0 Support
- NEW RS0802 KV20000 motors
- 1080P HD Video record
- Blackbox Ready support GYROFLOW
- Smooth and powerful performance
- Compatible for 1S Lipo/LIHV
- Recommended 1S 450mah/550mah/650mah batteries (Not included)
Specifications
- Brand Name: Happymodel
- Item Name: Mobula7 1S HD 75mm Micro FPV whoop drone
- Wheelbase: 75mm
- Size: 99mm*99mm*45.5mm
- Weight: 33g
- Receiver option: SPI 2.4GHz ELRS V2.0 / SPI Frsky D8/D16
Motor Specifications
- Mode: RS0802 KV20000
- Configuration: 9N12P
- Stator Diameter: 8mm
- Stator Length: 2mm
- Shaft Diameter: Φ1.5mm
- Motor Dimension(Dia.*Len): Φ10.5mm*13.5mm
- Weight: 2.0g
- No. of Cells (Lipo): 1S only
Propeller Specifications
- Weight: 0.24g
- Material: PC
- Pitch: 1 inch
- Props Diameter: 40mm
- Center Thickness: 5mm
- Center Hole Diameter: 1.5mm
[The rest of the specifications]
Package Contents
- 1x Mobula7 1S 75mm whoop Drone Frame (Mobula7 v4 frame)
- 1x Flight Controller AIO ESC Receiver vtx
- 4x RS0802 KV20000 brushless motor
- 2x Gemfan 1610-2 bi-blade propellers CW
- 2x Gemfan 1610-2 bi-blade propellers CCW
- 1x Runcam Split3-Lite Camera
- 1x External Blackbox Module supporting gyroflow
- 1x Propeller disassembly tool
- 1x 1S series balance charging board
Product Specifications
| Motor |
Mode: RS0802 KV20000
Configu-ration:9N12P
Stator Diamter:8mm
Stator Length:2mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.*Len):Φ10.5mm*13.5mm
Weight(g):2.0g
No.of Cells(Lipo):1S only
|
| Propeller |
Weight:0.24g
Material:PC
Pitch:1 inch
Props Dia:40mm
Center Thickness:5mm
Center Hole Dia:1.5mm
|
| Flight Controller |
X12 ELRS V2.0 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM20689(SPI connection)
Mount hole size: 25.5mm*25.5mm
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OpenVTX 0mw~400mw
Built-in ExpressLRS 2.4G,Frsky D8/D16
Built-in voltage detection
Built-in current sensor
|
Onboard 4in1 ESC
|
Power supply: 1S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: Z_H_30_REV16_7.HEX
Default protocol: DSHOT300
Support Bluejay firmware
When use Blujay firmware with 48khz, should set startup power to 1100/1200
|
| Onboard SPI ExpressLRS 2.4GHz Receiver |
Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V2.0
RF Frequency: 2.4GHz
Antenna : Enameled copper wire length 30mm
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Compatible with ExpressLRS V2.0 TX Module
Couldn’t flash separately ExpressLRS firmware
|
Onboard Frsky SPI D8/D16 receiver Version
|
Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V2.0
RF Frequency: 2.4GHz
Antenna : Enameled copper wire length 30mm
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Compatible with ExpressLRS V2.0 TX Module
Couldn’t flash separately ExpressLRS firmware
|
Onboard 5.8g OPENVTX
|
Firmware version: OPENVTX
Smartaudio v2.1
PIT Mode support
RCE Mode support
Channels:48ch
Transmitting Power: 0/RCE/25mw/100mw/400mw
Power supply: DC 5V
Current (5v): <650ma (400mw)
|
Runcam Split3-Lite
|
Model: RunCam Split3-Lite
Field of View(FOV):Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
Video Resolution:1080@60fps/1080@50fps/1080@30fps/720@60fps
Video File Format: MOV
Image Resolution:2 MP
TV Mode: NTSC (720*480)/PAL (720*576) Switchable
Interface: JST 1.25mm / UART and SH 1.0mm
Max Micro SD Card Supported 64G(need Class 6 or above, recommend Class 10/UHS-I/UHS-II/UHS-III)
Hole Distance of Installation: 25.5*25.5mm
PCB Size: 29*29mm
Lens Module Size: 14*14mm
Lens Specs: M9
Power Input: DC 5-20V(Non-direct power supply from battery. Powered directly with battery will generate surges and burn the camera.)
Working Current: 450mA @5V |
External Blackbox |
Size:18*15.5*4.5
With Built-in Voltage booster module
Weight:1.5gram
SD Card support max to 32GB
SD Card need to use FAT32 Format
Notes: Need to careful to insert the TF SD Card , and don't pull it out while install the battery.
|
Product Images
Free
3-7 Day
Tracked Delivery
Easy 30 Day Returns
Black Friday Event - Best Price Guarantee
